Featuring:
4 AVAILABLE - 2" x .134" Dahlstrom Stainless Tube Mill Lines
- Tube Diameter: .625" - 2"
- Wall Thickness: .020" - .134"
- Speed: 90 - 165 inches/min
- 12" x 2500# Cooper Weymouth Double End Uncoiler (8" - 20" Coil ID, 48" OD, Electric Brake)
- Forming Mill: Model 500-10-08 (Shaft Size: 2.5")
- Entry Brush De-Burr Unit, 2 Sets of Edge Guides, 5 Forming Stands, 3 Finn Pass Stands, 7 Side Idler Rolls
- 2 Roll Weld Box, Mill Maxstar 700 Tig Welder, Cyclomatic Model 90A Arc Controller, Water Cooler, Hammer Roll Bead Roller
- 3 Sizing Stands, 3 Side Idler Rolls, Turks Head, Flying Abrasive Saw Cut-Off, Run Out Dump Table
- Single Motor Mill, Siemens Simatic HMI Digital Controller, Yaskawa Digital Drive, Siemens Simatic S7-1200 PLC
- 150 KW Ajax Tocco Power Supply, Model Pacer S10
Sunbeam Roller Hearth Bright Annealing Furnace
- Max Operating Temperature: 2200°F
- Furnace Width: 48", Furnace Length: 30', Cooling Length: 60'
- Capacity: 5000 lbs/hr Tubing
- 3 Zones, Hydrogen, Nitrogen, Argon Gases
- Atmosphere Engineering Flow Controller, Hydrogen/Nitrogen Atmosphere Controlled
- Cooling Zone with Water Cooled Trays, Seco Warwick Digital Controls, Digital Atmosphere Control Panel
- Entry & Exit Conveyors
1.125 Etna Swedger
- 1.250" - .280" Diameter
- Clamping Device, Hydraulic Unit, Tooling
1 3/4" Mackintosh Hemphill Tube Straightener
- Serial No. 922
- Tube Diameter: 1.750" - .313"
- 6 Roll Design, Entry & Exit Tables
- Manual Roll Adjustment with Readouts, 2 Motor Drive
Ingersoll Rand Air Dryer
- Model: TMS 0780
- Max Air Pressure: 232 Bar 16
- Min & Max Ambient Temp: 32°F / 115°F
- Max Inlet Air Temp: 131°F
- Design Press: 14.5 PSI (1 bar) to 146 PSI (17 bar)
Gardner Denver Air Compressor
- Model: 2449-436
- 150 HP
- MAWP: 150 PSI @ 250°F
- MDMT: -20°F @ 150 PSI
Ingersoll Rand Air Compressor
- Model: SSR-EP150
- Capacity: 670 CFM
- Rated Operating Pressure: 125 PSIG
- Max Discharge Pressure: 128 PSIG
- Drive Motor: 150 HP
300 Ton Evapco Cooling Tower (NEW)
- Model: USS-112-4M14
- Belt No. 6B148
- 2 Armstrong Pumps (Model: 4300-8x8x15-4p-100hp)
- Flow: 1500 USgpm, 100 HP Motor, Max Pressure: 175 PSI
- 1500 gpm pump
#3 Sink Bench/Draw Bench
- Diameter Range: 2 3/8" - 3/8", Tube Length: 120'
- Wall Thickness: .020" - .191"
- Draw Force: 39,345#
- Draw Chain Speed: 209 Feet/Min
- Single Chain, Single Die Block, 250 HP Motor, 3 Snubbers
- Entry & Exit Conveyors, Tooling
#3 Draw Bench Cell
- Diameter Range: 2 3/8" - 3/8", Tube Length: 120'
- Wall Thickness: .020" - .191"
- Draw Force: 48,802#
- Draw Chain Speed: 169 Feet/Min
- Single Chain, Single Die Block, 250 HP Motor
- Entry & Exit Conveyors, Ultrasonic Bar Washer (2021), Wash & Rinse Tanks
- Bar Loader Conveyor, Tube Conveyor, Reeler To Remove Inner Mandrel Bars, Tooling
#2 Sink Bench
- Diameter Range: 2 3/8" - 3/8", Tube Length: 120'
- Wall Thickness: .020" - .191"
- Draw Force: 39,345#
- Draw Chain Speed: 209 Feet/Min
- Single Chain, Single Die Block, 250 HP Motor, 3 Snubbers
- Siemens Panelview 550 Digital Controller, Ultrasonic Tube Wash, Siemens Simatic HMI
- Entry & Exit Conveyors, Tooling
#2 Draw Bench Cell
- Diameter Range: 2 3/8" - 3/8", Tube Length: 120'
- Wall Thickness: .020" - .191"
- Draw Force: 48,802#
- Draw Chain Speed: 169 Feet/Min
- Single Chain, Single Die Block, 250 HP Motor
- Bar Wash, Bar Feed Conveyor, Siemens Simatic HMI Digital Controller
- Reeler To Remove Inner Mandrel Bars From Tubes, Tube Conveyor, Entry & Exit Conveyors, Tooling
Savage Abrasive Tube Cutting Saw
- Capacity: 24" Wide Layer of Tubes
- Inlet & Outlet Conveyor
- Back Stop, Dust Collector, Spare Blades
- Top & Bottom Clamps
Satec Systems Tensile Tester
- U.T.M Model Vertex 60HVL
- Serial No. 1600 with Instron System ID 60HVL C1600 & Monitor & Printer
Large Amount Of Tooling, MRO, Racking, Welders, Toolroom Equipment & Much More…
Contact
Shawn Gaffney
562-480-3041
shawn@hollandindustrialgroup.com
.svg)
.svg)
.svg)